The Self Canceling Turn Signal Module™ is an electronic flashing relay that is meant to completely replace your existing mechanical flashing relay(s), or be a stand alone flashing relay to vehicles that do not have turn signals. It works with both LEDs or incandescent lights up to 10 amps per output(20 Amps Max). This module does not require any load equalizers because it is a self-timed electronic relay.
Please Note:The Self Canceling Turn Signal Module™ requires momentary push buttons to operate (not included). Latching-type switches, or push to cancel type switches, will not work properly because these types of switches send constant power to your turn signals when on and will defeat the main purpose of the self canceling feature.
• No flasher relay needed
• 3 user selected flash periods
• Automatically self-cancels
• Works with LEDs and incandescent
• Hazard flasher feature built in
• Waterproof and heat resistant
Turn Signal Modes
Mode 1 : Press turn signal button for 1 second, turn signal light will flash for 7 seconds, then self cancel. This mode is usually used when changing lanes.
Mode 2 : Press turn signal button for 2 seconds, turn signal light will flash for 20 seconds, then self cancel. This mode is usually used when slowing down to go around a corner.
Mode 3 : Press turn signal button for 4 seconds, turn signal light will flash for 75 seconds, then self cancel. This mode is usually used when stopping at a signal light and turn will be made after stopping.
Note: All three modes above can be cancelled by pressing the same turn signal button a second time.
Mode 4 : Hazard Mode - is available all the time and will flash until cancelled. To engage, depress both the left and right turn signal buttons for 1 second. To cancel, depress both buttons again for one second.
Part Number: 01501
Weight: Less than 1lb
Amp Limit: 10 Amp Per Output (20 Amps Max)
System Requirement: 12VDC(-)
Attachment Method: Included Double Sided Adhesive Pad
Height (in): 5/8"
Length (in): 2 1/4"
Width (in): 1 5/8"
Wire Length: 5"-6"
Material: Anodized Aluminum Case with Heat and Water Resistant Potting
Wire: 16AWG - 20AWG
Package Contents: (1) Self Canceling Turn Signal Module™, (1) Adhesive Mounting Pad
Color / Finish: Black Anodized
Hardware Included: No
Connectors Included: No
Tools Required: Wire Cutters/Splices
Water Resistant: Yes
Heat and Vibration Resistant: Yes
Companion Product(s): n/a
Having a difficult time deciding which module best suits your needs? Take a look below to see the differences between them!
Signal Dynamics Corporation warranties this product at time of purchase to be free from defects in material and workmanship to the original purchaser. Signal Dynamics Corporation's obligation under the warranty is limited to repairing or exchanging the unit if the unit is returned with the postage prepaid to Signal Dynamics Corp. within 1 year from the date of purchase. The warranty is void if the unit has been incorrectly installed, damaged, or tampered with. This warranty specifically limits Signal Dynamics Corporation's liability to unit replacement only and specifically excludes any consequential damage arising from use proper or improper or failure to properly function. A copy of your purchase receipt or other proof of purchase is required when applying for warranty consideration. See full Warranty and Return Policy!
Posted by Maxx on 31st May 2019
Have a 1978 Suzuki GS1000E (The Fast One), I purchased in 1978. It had a high tech (for its time), auto cancelling signal system. It would stay on until the speedo sent pulses indicating you were now moving and would soon cancel. It lasted a season or two. Over the years I've purchased used ones (with no guarantees) from salvage yards. None of them worked. The last one almost worked but would turn on the right signal by itself and with much fiddling, I could get it off. Now after about 39years I can stop flapping my arms to signal. Using the factory handlebar turn signal switch, six wires and I'm good to go. It does help if you have the wiring diagram for your bike but even without it one can easily figure things out with the supplied wiring diagram.
Posted by Benjamin Jr Salazar on 3rd Mar 2018
It's a experiences products I like that it easy to wire up nice thanks
Posted by Unknown on 23rd Sep 2017
Simplicity of design sophistication of function ! Great tech support.
Posted by Dave on 24th Nov 2016
pretty straight forward installation.
Posted by Unknown on 2nd Sep 2016
Just what I have wanted for years. My 1984 FLH has always had the original PITA turn signal switches. So now updated to self cancelling and easy install.
Posted by Unknown on 2nd Jun 2016
I built my bike from the ground up. Didn't want to put bulky turn signals front and rear so I opted to go with a pair of LED mirrors. This module was just what I needed to make the signals operate correctly and it's nice and compact, easy to conceal.
Posted by Unknown on 16th Feb 2016
Works great in a custom application environment. Wiring diagram is on the front, no instructions needed.
Posted by jeeper james on 20th Dec 2015
To start and finish quickly my jeep steering column switches broke. So I decided I will just retire them that was a nightmare due to the fact it has trailer style wire . Got that done went to get it the required safety inspection and it was all toggle switches so the mechanic tells me my turn signals are not Self canceling so I don't pass. So I search high and low finally found the self canceling turn signal module bam I'm now road worthy thank you Signal Dynamics.
Posted by Blair on 7th Jun 2015
So glad this was recommended by other Cobra replica builders. Quick and easy installation - perfect results.
Posted by mike on 11th Apr 2015
Nice and easy upgrade for early bikes. Only improvement would be the instructions. Had to search online to find what I needed wiring wise.