The BackOFF™ Brake Light Module automatically flashes your brake light(s) to capture the attention of following drivers and to make your motorcycle more visible. When installed, the motorcycle's brake light becomes significantly more noticeable because your brake light(s) modulates three short flashes followed by one steady-on pulse for four seconds. This pattern automatically repeats itself as long as the brakes are applied.
Note: This module will not work with LED brake lights. The BackOFF™ XP Brake Light Module with work with both standard incandescent and LED brake lights.
When you apply your brakes, it causes your brake light to automatically emit a visual alerting signal of 3 short light flashes, followed by 1 steady on light for 2 seconds. This signal automatically repeats itself as long as the brakes are applied. This pattern is not random, but has been selected because of its ability to gain and retain following driver's attention. Most states drivers handbooks recommend that you flash your brakes when slowing or stopping. The BackOFF™ automatically facilitates compliance and enhances safety. Install the BackOFF™ and see how much more effective your brake light can be.
To install, wire the BackOFF™ Brake Light Module in-line with your existing brake light wire. Locate your brake light wire and cut the wire into 2 (use a test light or multi-meter to find proper wire). Connect the red wire from the BackOFF™ Brake Light Module to the cut wire end leading toward the front of the motorcycle. Next connect the white wire with the red stripe to the cut wire leading toward the rear of the bike. Finally peel the paper lining off of the double sided adhesive pad and mount the module to a clean, flat surface.
Solder connections or use crimp connectors (not included)
Red Wire: Brake Light Wire Leading toward front of Bike
White Wire with Red Stripe: Brake Light Wire Leading toward Bulb
Part Number: 01001
Weight: Less than 1lb
Amp Limit: 10 Amp Max (up to 3 Standard Incandescent Bulbs)
System Requirement: 12VDC(-)
Attachment Method: Included Double Sided Adhesive Pad
Height (in): 5/8"
Length (in): 2 1/4"
Width (in): 1 5/8"
Wire Length: 5"-6"
Material: Anodized Aluminum Case with Heat and Water Resistant Potting
Wire: 16AWG - 20AWG
Package Contents: (1) BackOFF™ Brake Light Module, (1) Adhesive Mounting Pad
Color / Finish: Black Anodized
Hardware Included: No
Connectors Included: No
Tools Required: Wire Cutters/Splices
Water Resistant: Yes
Heat and Vibration Resistant: Yes
Companion Product(s): n/a
Signal Dynamics Corporation warranties this product at time of purchase to be free from defects in material and workmanship to the original purchaser. Signal Dynamics Corporation's obligation under the warranty is limited to repairing or exchanging the unit if the unit is returned with the postage prepaid to Signal Dynamics Corp. within 1 year from the date of purchase. The warranty is void if the unit has been incorrectly installed, damaged, or tampered with. This warranty specifically limits Signal Dynamics Corporation's liability to unit replacement only and specifically excludes any consequential damage arising from use proper or improper or failure to properly function. A copy of your purchase receipt or other proof of purchase is required when applying for warranty consideration. See full Warranty and Return Policy!
Previous | Showing reviews 11-15 of 15
Posted by Jim S on 13th May 2014
This product was very easy to install and it works as advertised. This is the second one that I have purchased, and I would now consider this a must have for any street-going motorcycles that I acquire in the future.
Posted by WILDCARD SOUTH FLORIDA on 5th Mar 2014
ON MY GL 1800 WING ITS INSTALLED UNDER THE SEAT INTO THE
BREAK LIGHT FLASHER .... NOT IN THE TRUNK THIS IS A SIMPLE INSTALL NO WIRES TO ADD NO TIGHT SPACES IN TRUNK TOURPACK
AND IT FLASHES ALL REAR BREAK LIGHTS ... NOT JUST 2 LIKE TRUNK HOOKUP ... SAFE TIME SAFE TROUBLE DO IT THIS WAY
Posted by Gary Gissiner on 23rd Jan 2014
I have a Harley Wide Glide which is a great bike, but most accessory notes say all except 2012 up Wide Glides but not Signal Dynamics Corporation they make a universal brake light flasher that not only fits but it works great and is reasonably priced. I can tell you after may hours of searching the web this is a great product. It took me about 45 minutes to install this device with the hardest part was to get someone to tell me what color wire went to my brake lights. I have used another brand on other bikes I've owned and this unit is as good and in some respects better for less money. Good job guy's.
Posted by wildcard on 2nd Dec 2013
I WENT TO A MECHANIC HE WIRED IT INTO MY BIKE
IT WORKS PERFECT IT WAS EXACTLY WHAT I WANTED
FOR MY HONDA GOLDWING
IF YOU WANT TO KNOW MORE ASK ME
Installed in 15 minutes works 4 break lights
Posted by Unknown on 13th Nov 2013
This module is so quick and easy to install, I will never ride without a Backoff again!
Previous | Showing reviews 11-15 of 15